null

Ski & Snowboard Skuff Saver Tape (sold per foot)

(12 reviews) Write a Review
AUD $4.24
SKU:
TYC 7210

Product Overview

This thick, clear tape will protect the tops of your skis or snowboard from scratches and gouges while allowing the graphics to show through. The tough, translucent Dupont Surlyn tape is backed with a self-adhesive film for easy application and excellent bonding. 

  • The tape is 14-inches wide...enough to span any single snowboard or pair of skis.
  • 0.3mm thick
  • Simply order the length you need and trim the width with a razor knife to fit your needs.
  • Not recommended for textured top sheets.
  • It is sold by the foot, so (for example) if you enter 6 for the quantity you'll receive a 6-foot length of Skuff Saver.
  • If you have a Pair of skis that measure 180cm long you would order 6-feet of skuff saver.
  • If you have a snowboard that measures 150cm you would order 5-feet of skuff saver.

Installation Tips:

  1. Clean top sheet of ski or snowboard with isopropyl rubbing alcohol using a lint-free cloth (ie. an old t-shirt).
  2. Trim any excess material from preexisting gouges carefully with a razor blade so the tape will sit flat.
  3. If applying to a pair of skis, cut the tape in half length wise so you have two pieces.
  4. Determine the appropriate length for the tip and tail of the ski or snowboard. It is best to measure from the toe piece to the tip and the heel piece to the tail. On a snowboard measure from front binding to tip and rear binding to tail. 
  5. Cut the appropriate length erring on the side of longer than you think you need.
  6. Start to peel the backing tape at one end, start at the toe piece and work toward the tip, stick the tape to the top sheet being careful to keep it straight.
  7. As you lay down the tape peel away the backing, make sure to go slowly and press out air bubbles as you go. If you miss one you can peel the tape back a bit, remove the bubble and continue.
  8. Use the same technique for the tail of the ski.
  9. Now it's time to trim the tape to the shape of the ski using a razor blade, I find the blades commonly used in razor knives work better that the thinner common razor blades (see photo).
  10. Keep in mind the tape will not stick well to the vertical sidewalls of skis, or to the angled portion of a cap ski, the tape is only for the actual top of the top sheet.

Reviews

(12 reviews) Write a Review

12 Reviews Hide Reviews Show Reviews

  • 5
    A must have

    Posted by Omar on Nov 18, 2019

    Honestly this is a must have if you care a bit about your nice looking snowboard topsheet. It's a relatively inexpensive way to protect your board from stupid scratches that happen on chair lifts for exemple. I would not recommend it for textured topsheets though.

  • 3
    looked awful - at least on my skis

    Posted by Marty Blank on Oct 30, 2019

    While I'm sure this product would do a great job protecting my skis from scuffs and chips (especially because I'm an instructor, with lots of people constantly sliding over my gear) it looked awful on my brand new, solid flat-black Blizzard Brahmas. Every/any imperfection stood out like a sore thumb and I also had trouble trying to apply it without any bubbles appearing. If your skis/snowboard has any type of design, this stuff should look and work great.

  • 5
    Skuff Saver Tape

    Posted by Brett on Oct 30, 2019

    Reasonably priced, shipped quickly and well packaged. Exactly what I ordered and wanted.

    Finding a product like this that's wide enough isn't that difficult. Being able to find it by-the-foot for a reasonable cost is harder than you think. Thanks!!

  • 5
    Skuff Saver Tape

    Posted by Darrell on Feb 25, 2019

    Great product and price! Installed on my new skis to protect the top from scuffs and scratches. Easy to install and you can’t tell it is on your ski. Also quick delivery.
    Thanks Tognar.

  • 5
    Clear coat

    Posted by 5o7graphics on Jul 11, 2018

    This would be the 8th board I have put this on and it works very well. The one trick that I have found is to let the board and vinyl sit in the summer sun for 30 minutes. You will get fewer bubbles.

  • 5
    We love this stuff

    Posted by 5o7graphics on Jun 22, 2018

    We love this stuff and we have installed it on 7 snowboards. The people there are AWESOME to work with. Also cheap and fast shipping!

  • 4
    Great protection for my teaching skis.

    Posted by Earl on Mar 24, 2018

    Nice and thick. Should really work well.

  • 5
    skuff saver works

    Posted by Unknown on May 17, 2014

    I use the snowboard skuff saver for a different purpose. I use it as a gap seal between the stabilizer and the elevator on my airplane. I cut it into 2" strips and put the sticky side together with a 1" lap that gives me a 3" wide piece with a 1" sticky on the top and a 1" sticky on the bottom then apply centered on the gap in the control surface.

  • 4
    Works well

    Posted by Unknown on Mar 19, 2014

    I cut this to size and put it on my board in about 10 minutes. It seems pretty thick and protective.